Reef Photo will be closed Saturday, October 31st and Saturday, November 7th.

Quick Setup Guide: Nauticam NA-X2DII Housing for the Hasselblad X2D II

While full frame mirrorless cameras dominate the underwater photography market, there is another contender on the horizon. In bygone days, medium format photography was so staggeringly out of most people's budgets as to be laughable if one thought about it, and typically it wasn't even thought about.

However, Fuji and Hasselblad seem determined to change that. While modern medium format cameras are by no means cheap, both companies are bringing medium format into the realm of affordable. 

Enter the Hasselblad X2D II. With a laundry list of eye-popping specs, the X2D II feels like we finally might have a medium format camera with the performance to warrant taking it underwater. The camera features 102mpx medium format sensor and autofocus tracking that seems up to the task. Let's go through the proper way to set up the X2D II in Nauticam's dedicated housing so those medium format lovers out there can take their cameras underwater with confidence!

The Hasselblad X2DII Leaf Shutter

One of the most distinctive features of the Hasselblad X2D II is its leaf shutter, which offers a significant advantage for underwater photographers who use strobes. Unlike shutters found in most mirrorless cameras, a leaf shutter is built into the lens and opens and closes within the lens assembly, allowing the entire sensor to be exposed all at once. This enables flash synchronization at much higher shutter speeds, similarly to how the Sony A9III global shutter can expose the entire sensor at the same time instead of line by line.

Most mirrorless cameras have a standard flash sync speed of around 1/160–1/250s, while some models, such as the Sony A1, can reach 1/400s. The aforementioned Sony A9III is a notable exception, thanks to its global shutter. The Hasselblad X2D II, however, can synchronize with flash at shutter speeds of up to 1/4000s when paired with compatible XCD lenses.

However, there is an important consideration when choosing strobes to pair with the X2D II: not every strobe can deliver its full output at shutter speeds as fast as 1/4000s.

This comes down to flash duration. Flash duration is the length of time the strobe emits light. Depending on the strobe's design and power setting, its flash duration may be too long to deliver the entire light pulse while the camera's shutter is effectively exposing the sensor. The result can be reduced effective output or uneven exposures.

If you're considering the X2D II, it is worth researching how your chosen strobes perform at faster sync speeds, rather than relying solely on the camera's maximum specification. Ideally, you'll want strobes that can synchronize reliably at high shutter speeds while retaining as much usable power as possible.

The NA-X2DII housing for the Hasselblad X2DII Medium Format camera.

The Hasselblad X2DII with the XCD 20-35, next to the NA-X2DII housing

As with all Nauticam's housings the NA-X2XII features phenomenal ergonomics, providing access to all of the camera's important controls. First up is the new version of Nauticam's N120 bayonet mount for installing your various ports. 

Port Installation

The NA-X2DII features Nauticam's new version of their bayonet port lock mechanism. Simply push the port onto the front of the housing, wait to hear the satisfying click, and your port (or extension ring) is mounted! To mount a port on an extension ring, make sure the latch on the extension ring is opened. Push the port onto the extension, lining up the white dots, and snap the latch shut. If there is any when closing latches, the port or extension are not seated properly, do not force it.

Vacuum Installation

The NA-X2DII housing features two M16 accessory ports and an M24 accessory port. Use one of the M16 ports for an accessory vacuum valve. Installation is extremely easy. Remove the M16 bulkhead cap, thread the vacuum bulkhead into place, and use the tightening tool (included with the vacuum valve) to ensure the bulkhead is snug. Don't forget to put cap back on!




Camera Installation

As with every camera mounted into a Nauticam housing, the housing has a tray or sled that threads into the tripod mount on the bottom of the camera and the X2DII is no exception. Simply place the camera onto the tray, line up the tripod hole, and thread the tray onto the camera before sliding the whole rig back into the housing.

Flash Trigger Installation

When using flashes triggered via fiber optics with the X2DII, you need to use the LED flash trigger. The flash trigger slots into the hotshoe on top of the camera body and triggers flashes via LED pulses up through the fiber optic ports on the top of the NA-X2DII Housing. When turned on, there will be a green LED active to let you know the trigger is on and ready to fire.

Reef Photo & Video

4760 Woolbright Road, Suite 105, Boynton Beach, FL 33436

954-537-0644 · Toll free 1-877-453-8927

Mon–Fri 10am–6pm · Sat 10am–5pm · Closed Sunday